Ramps 1.4 Full Graphic Smart Display - Klipper Setting

Standard Settings für das Ramps 1.4 mit dem RepRap Fullgraphic Smart Display

Diese Einstellungen sind für die Verwendung in meinem Eigenbau S1 Skalierbarer kartesische FDM 3D Drucker zum Nachbauen. 

Code der printer.cfg

# This file contains common pin mappings for RAMPS (v1.3 and later)
# boards. RAMPS boards typically use a firmware compiled for the AVR
# atmega2560 (though the atmega1280 is also possible).

[include mainsail.cfg]

# See docs/Config_Reference.md for a description of parameters.

[stepper_x]
step_pin: PF0
dir_pin: PF1
enable_pin: !PD7
microsteps: 16
rotation_distance: 40
endstop_pin: ^PE5
#endstop_pin: ^PE4
position_endstop: 0
position_max: 200
homing_speed: 50

[stepper_y]
step_pin: PF6
dir_pin: !PF7
enable_pin: !PF2
microsteps: 16
rotation_distance: 40
endstop_pin: ^PJ1
#endstop_pin: ^PJ0
position_endstop: 0
position_max: 200
homing_speed: 50

[stepper_z]
step_pin: PL3
dir_pin: PL1
enable_pin: !PK0
microsteps: 16
rotation_distance: 8
endstop_pin: ^PD3
#endstop_pin: ^PD2
position_endstop: 0.5
position_max: 200

[extruder]
step_pin: PA4
dir_pin: PA6
enable_pin: !PA2
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PB4
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK5
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 250

#[extruder1]
#step_pin: PC1
#dir_pin: PC3
#enable_pin: !PC7
#heater_pin: PH6
#sensor_pin: PK7
#...

[heater_bed]
heater_pin: PH5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK6
control: watermark
min_temp: 0
max_temp: 130

[fan]
pin: PH6

[mcu]
#serial: /dev/ttyACM0
serial: /dev/serial/by-id/usb-Arduino__www.arduino.cc__0042_75834353930351B06162-if00


[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100

# Common EXP1 / EXP2 (display) pins
[board_pins]
aliases:
    # Common EXP1 header found on many "all-in-one" ramps clones
    EXP1_1=PC0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=<GND>,
    EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
    # EXP2 header
    EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0, EXP2_9=<GND>,
    EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PG0, EXP2_10=<RST>
    # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
    # Note, some boards wire: EXP2_8=<RST>, EXP2_10=PG0




######################################################################
# "RepRapDiscount 128x64 Full Graphic Smart Controller" type displays
######################################################################

[display]
lcd_type: st7920
cs_pin: EXP1_4
sclk_pin: EXP1_5
sid_pin: EXP1_3
encoder_pins: ^EXP2_3, ^EXP2_5
click_pin: ^!EXP1_2
#kill_pin: ^!EXP2_8

[output_pin beeper]
pin: EXP1_1